Knowing Essential Plumbing Skills is Important When Installing a Bathtub

Knowing Essential Plumbing Skills is Important When Installing a Bathtub

Blog Article

Click Here

This post below on the subject of Tools You Need to Install a New Bathtub is quite attention-grabbing. Don't miss it.

Installing a bath tub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bathtub with a new one is also a moderately tough job. If the old tub is conveniently available, the project can move quickly; if you have to open a wall surface to get rid of the old tub as well as place the brand-new tub, the job is a lot harder. In either instance, the project is within a house handyman's skills, although you will certainly require a helper to leave the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job and fit attempting it. Instead of employing a contractor to take control of a halfway-completed project, it is much better to think about using one prior to you start. Chances are you may need a professional plumber to make tube links.
This write-up will aid you install a brand-new bath tub in your washroom if you have actually already bought a brand-new tub and do not require to alter the setup of your previous supply of water pipes.
Your devices and material checklist must consist of the following:

New Bathtub

Hammer

Pipe Wrenches

Prybar

Safety Glasses

Level

Pliers

Adjustable Wrench

Putty Blade

Screwdriver

Cold Blade

Measuring tape

Pipe Caps

Planning for the Installment

To start with, the supporting structure provided with the bathroom should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of both faucets making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last position.

Removing Old Taps

If you need to replace old faucets with new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the restricted gain access to that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will originate from the pipes. Once the supply pipes have been eliminated, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the brand-new faucets, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.

Setting up the Bathtub

Utilizing both wooden boards under its feet, place the bath tub in the needed placement. The wooden boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to ensure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bathtub up until the spirit level reviews degree.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Activate the water as well as inspect all joints and also new pipework for leaks and tighten them if required. Load the tub as well as additionally examine the overflow outlet as well as the normal electrical outlet for leakages.
Lastly, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the tub has actually been made use of a minimum of once as this will settle it right into its final position.

Suitable New Taps

If the tails of the brand-new taps are plastic, then you will need a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making sure that the washing machines are in area between the faucet and the sink. Protect the faucet in position with the supplier offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

Tiling Around the Bathtub

In the location where the bathroom meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a rigid seal, creating the water to permeate the wall surface in between the bathroom and the tiling, leading to difficulties with moisture as well as feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to enable the activity experienced when the tub is in use. The sealer can break rather early if you do not think about this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Do you enjoy reading about A Step-by-Step Guide to Installing a Bathtub? Post feedback directly below. We will be interested to find out your suggestions about this content. We are looking forward to see you back again in the future. Liked our write up? Please share it. Let other people find it. I value reading our article about Tools You Need to Install a New Bathtub .

Request Appointment

Report this page